By Exam Number 200-125 CCNA
Associated Certifications CCNA Routing and Switching
Duration 90 Minutes (50-60 questions)
Available Languages English, Japanese
This exam tests a candidate’s knowledge and skills related to network fundamentals, LAN switching technologies, IPv4 and IPv6 routing technologies, WAN technologies, infrastructure services, infrastructure security, and infrastructure management.
The Cisco Certified Network Associate (CCNA) Routing and Switching composite exam (200-125) is a 90-minute, 50–60 question assessment that is associated with the CCNA Routing and Switching certification. This exam tests a candidate’s knowledge and skills related to network fundamentals, LAN switching technologies, IPv4 and IPv6 routing technologies, WAN technologies, infrastructure services, infrastructure security, and infrastructure management.
The following topics are general guidelines for the content likely to be included on the exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.
Subscribe to Cisco Learning Network Premium and access the most comprehensive e-learning training, resources and tools you’ll need to prepare for your CCENT, CCNA and CCNP Routing and Switching certifications.
1.0 Network Fundamentals 15%
1.1 Compare and contrast OSI and TCP/IP models
1.2 Compare and contrast TCP and UDP protocols
1.3 Describe the impact of infrastructure components in an enterprise network
1.3.a Firewalls
1.3.b Access points
1.3.c Wireless controllers
1.4 Describe the effects of cloud resources on enterprise network architecture
1.4.a Traffic path to internal and external cloud services
1.4.b Virtual services
1.4.c Basic virtual network infrastructure
1.5 Compare and contrast collapsed core and three-tier architectures
1.6 Compare and contrast network topologies
1.6.a Star
1.6.b Mesh
1.6.c Hybrid
1.7 Select the appropriate cabling type based on implementation requirements
1.8 Apply troubleshooting methodologies to resolve problems
1.8.a Perform and document fault isolation
1.8.b Resolve or escalate
1.8.c Verify and monitor resolution
1.9 Configure, verify, and troubleshoot IPv4 addressing and subnetting
1.10 Compare and contrast IPv4 address types
1.10.a Unicast
1.10.b Broadcast
1.10.c Multicast
1.11 Describe the need for private IPv4 addressing
1.12 Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a LAN/WAN environment
1.13 Configure, verify, and troubleshoot IPv6 addressing
1.14 Configure and verify IPv6 Stateless Address Auto Configuration
1.15 Compare and contrast IPv6 address types
1.15.a Global unicast
1.15.b Unique local
1.15.c Link local
1.15.d Multicast
1.15.e Modified EUI 64
1.15.f Autoconfiguration
1.15.g Anycast
2.0 LAN Switching Technologies 21%
2.1 Describe and verify switching concepts
2.1.a MAC learning and aging
2.1.b Frame switching
2.1.c Frame flooding
2.1.d MAC address table
2.2 Interpret Ethernet frame format
2.3 Troubleshoot interface and cable issues (collisions, errors, duplex, speed)
2.4 Configure, verify, and troubleshoot VLANs (normal/extended range) spanning multiple switches
2.4.a Access ports (data and voice)
2.4.b Default VLAN
2.5 Configure, verify, and troubleshoot interswitch connectivity
2.5.a Trunk ports
2.5.b Add and remove VLANs on a trunk
2.5.c DTP, VTP (v1&v2), and 802.1Q
2.5.d Native VLAN
2.6 Configure, verify, and troubleshoot STP protocols
2.6.a STP mode (PVST+ and RPVST+)
2.6.b STP root bridge selection
2.7 Configure, verify and troubleshoot STP related optional features
2.7.a PortFast
2.7.b BPDU guard
2.8 Configure and verify Layer 2 protocols
2.8.a Cisco Discovery Protocol
2.8.b LLDP
2.9 Configure, verify, and troubleshoot (Layer 2/Layer 3) EtherChannel
2.9.a Static
2.9.b PAGP
2.9.c LACP
2.10 Describe the benefits of switch stacking and chassis aggregation
3.0 Routing Technologies 23%
3.1 Describe the routing concepts
3.1.a Packet handling along the path through a network
3.1.b Forwarding decision based on route lookup
3.1.c Frame rewrite
3.2 Interpret the components of a routing table
3.2.a Prefix
3.2.b Network mask
3.2.c Next hop
3.2.d Routing protocol code
3.2.e Administrative distance
3.2.f Metric
3.2.g Gateway of last resort
3.3 Describe how a routing table is populated by different routing information sources
3.3.a Admin distance
3.4 Configure, verify, and troubleshoot inter-VLAN routing
3.4.a Router on a stick
3.4.b SVI
3.5 Compare and contrast static routing and dynamic routing
3.6 Compare and contrast distance vector and link state routing protocols
3.7 Compare and contrast interior and exterior routing protocols
3.8 Configure, verify, and troubleshoot IPv4 and IPv6 static routing
3.8.a Default route
3.8.b Network route
3.8.c Host route
3.8.d Floating static
3.9 Configure, verify, and troubleshoot single area and multi-area OSPFv2 for IPv4 (excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
3.10 Configure, verify, and troubleshoot single area and multi-area OSPFv3 for IPv6 (excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
3.11 Configure, verify, and troubleshoot EIGRP for IPv4 (excluding authentication, filtering, manual summarization, redistribution, stub)
3.12 Configure, verify, and troubleshoot EIGRP for IPv6 (excluding authentication, filtering, manual summarization, redistribution, stub)
3.13 Configure, verify, and troubleshoot RIPv2 for IPv4 (excluding authentication, filtering, manual summarization, redistribution)
3.14 Troubleshoot basic Layer 3 end-to-end connectivity issues
4.0 WAN Technologies 10%
4.1 Configure and verify PPP and MLPPP on WAN interfaces using local authentication
4.2 Configure, verify, and troubleshoot PPPoE client-side interfaces using local authentication
4.3 Configure, verify, and troubleshoot GRE tunnel connectivity
4.4 Describe WAN topology options
4.4.a Point-to-point
4.4.b Hub and spoke
4.4.c Full mesh
4.4.d Single vs dual-homed
4.5 Describe WAN access connectivity options
4.5.a MPLS
4.5.b Metro Ethernet
4.5.c Broadband PPPoE
4.5.d Internet VPN (DMVPN, site-to-site VPN, client VPN)
4.6 Configure and verify single-homed branch connectivity using eBGP IPv4 (limited to peering and route advertisement using Network command only)
4.7 Describe basic QoS concepts
4.7.a Marking
4.7.b Device trust
4.7.c Prioritization
4.7.c. [i] Voice
4.7.c. [ii] Video
4.7.c. [iii] Data
4.7.d Shaping
4.7.e Policing
4.7.f Congestion management
5.0 Infrastructure Services 10%
5.1 Describe DNS lookup operation
5.2 Troubleshoot client connectivity issues involving DNS
5.3 Configure and verify DHCP on a router (excluding static reservations)
5.3.a Server
5.3.b Relay
5.3.c Client
5.3.d TFTP, DNS, and gateway options
5.4 Troubleshoot client- and router-based DHCP connectivity issues
5.5 Configure, verify, and troubleshoot basic HSRP
5.5.a Priority
5.5.b Preemption
5.5.c Version
5.6 Configure, verify, and troubleshoot inside source NAT
5.6.a Static
5.6.b Pool
5.6.c PAT
5.7 Configure and verify NTP operating in a client/server mode
6.0 Infrastructure Security 11%
6.1 Configure, verify, and troubleshoot port security
6.1.a Static
6.1.b Dynamic
6.1.c Sticky
6.1.d Max MAC addresses
6.1.e Violation actions
6.1.f Err-disable recovery
6.2 Describe common access layer threat mitigation techniques
6.2.a 802.1x
6.2.b DHCP snooping
6.2.c Nondefault native VLAN
6.3 Configure, verify, and troubleshoot IPv4 and IPv6 access list for traffic filtering
6.3.a Standard
6.3.b Extended
6.3.c Named
6.4 Verify ACLs using the APIC-EM Path Trace ACL analysis tool
6.5 Configure, verify, and troubleshoot basic device hardening
6.5.a Local authentication
6.5.b Secure password
6.5.c Access to device
6.5.c. [i] Source address
6.5.c. [ii] Telnet/SSH
6.5.d Login banner
6.6 Describe device security using AAA with TACACS+ and RADIUS
7.0 Infrastructure Management 10%
7.1 Configure and verify device-monitoring protocols
7.1.a SNMPv2
7.1.b SNMPv3
7.1.c Syslog
7.2 Troubleshoot network connectivity issues using ICMP echo-based IP SLA
7.3 Configure and verify device management
7.3.a Backup and restore device configuration
7.3.b Using Cisco Discovery Protocol or LLDP for device discovery
7.3.c Licensing
7.3.d Logging
7.3.e Timezone
7.3.f Loopback
7.4 Configure and verify initial device configuration
7.5 Perform device maintenance
7.5.a Cisco IOS upgrades and recovery (SCP, FTP, TFTP, and MD5 verify)
7.5.b Password recovery and configuration register
7.5.c File system management
7.6 Use Cisco IOS tools to troubleshoot and resolve problems
7.6.a Ping and traceroute with extended option
7.6.b Terminal monitor
7.6.c Log events
7.6.d Local SPAN
7.7 Describe network programmability in enterprise network architecture
7.7.a Function of a controller
7.7.b Separation of control plane and data plane
7.7.c Northbound and southbound APIs
QUESTION 22
A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?
A. session
B. transport
C. network
D. data link
E. physical
Answer: D
Explanation:
The Data Link layer provides the physical transmission of the data and handles error notification, network topology, and flow control. The Data Link layer formats the message into pieces, each called a data frame, and adds a customized header containing the hardware destination and source address. Protocols Data Unit (PDU) on Datalink layer is called frame. According to this question the frame is damaged and discarded which will happen at the Data Link layer.
QUESTION 23
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?
A. Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B. Add a second router to handle the VLAN traffic.
C. Add two more Fast Ethernet interfaces.
D. Implement a router-on-a-stick configuration.
Answer: D
Explanation:
A router on a stick allows you to use sub-interfaces to create multiple logical networks on a single physical interface.
QUESTION 25
In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)
A. when they receive a special token
B. when there is a carrier
C. when they detect no other devices are sending
D. when the medium is idle
E. when the server grants access
Answer: C,D
Explanation:
Ethernet network is a shared environment so all devices have the right to access to the medium. If more than one device transmits simultaneously, the signals collide and cannot reach the destination.
If a device detects another device is sending, it will wait for a specified amount of time before attempting to transmit.
When there is no traffic detected, a device will transmit its message. While this transmission is occurring, the device continues to listen for traffic or collisions on the LAN. After the message is sent, the device returns to its default listening mode.
QUESTION 28
VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan 3 command in interface configuration mode?
A. The command is rejected.
B. The port turns amber.
C. The command is accepted and the respective VLAN is added to vlan.dat.
D. The command is accepted and you must configure the VLAN manually.
Answer: C
Explanation:
The “switchport access vlan 3” will put that interface as belonging to VLAN 3 while also updated the VLAN database automatically to include VLAN 3.
QUESTION 29
Which term describes a spanning-tree network that has all switch ports in either the blocking or forwarding state?
A. converged
B. redundant
C. provisioned
D. spanned
Answer: A
Explanation:
Spanning Tree Protocol convergence (Layer 2 convergence) happens when bridges and switches have transitioned to either the forwarding or blocking state. When layer 2 is converged, root bridge is elected and all port roles (Root, Designated and Non-Designated) in all switches are selected.
Click here to view complete Q&A of 200-125 exam
Certkingdom Review
Best Cisco 200-125 Certification, Cisco 200-125 Training at certkingdom.com
No Comment